Germany AWS DIN 17440 (1996), DIN 17441 (1997), DIN 17455 (1985), DIN 17456 (1985) , DIN 17457 (1985), DIN 17458 (1985), DIN EN 10028-7, DIN EN 10088-1, DIN EN 10088-2, DIN EN 10088-3, DIN EN 10088-4, DIN EN 10088-5, DIN EN 10216-5 (2004) , DIN EN 10217-7, DIN EN 10222-5, DIN EN 10250-4, DIN EN 10253-3, DIN EN 10253-4, DIN EN 10272, DIN EN 10296-2 (2005), DIN EN 10297-2 (2005) , X2CrNiMo18-14-3 Specialsteel Austenitic stainless steel. Grade 00Cr17Ni14Mo2 was replaced by new designation 022Cr17Ni12Mo2 according to GB/T 20878 (2007) and Mechanical Properties, Chemical Element, Cross Reference, Datasheet.
Category | Class | Grade | Type | Standard | Country | Application |
---|---|---|---|---|---|---|
Steel Grades | Specialsteel | X2CrNiMo18-14-3 | Austenite | AWS | Germany | Austenitic stainless steel. Grade 00Cr17Ni14Mo2 was replaced by new designation 022Cr17Ni12Mo2 according to GB/T 20878 (2007) |
C | Si | Mn | P | S | Ni | Cr | Mo |
---|---|---|---|---|---|---|---|
≤0.030 | ≤1.00 | ≤2.00 | ≤0.035 | ≤0.030 | 12.00 -15.00 | 16.00 -18.00 | 2.00 -3.00 |
Yield Rp0.2 (MPa) |
Tensile Rm (MPa) |
Impact KV/Ku (J) |
Elongation A (%) |
Reduction in cross section on fracture Z (%) |
As-Heat-Treated Condition | Brinell hardness (HBW) |
---|---|---|---|---|---|---|
698 (≥) | 636 (≥) | 33 | 14 | 42 | Solution and Aging, Annealing, Ausaging, Q+T,etc | 143 |
Temperature (°C) |
Modulus of elasticity (GPa) |
Mean coefficient of thermal expansion 10-6/(°C) between 20(°C) and | Thermal conductivity (W/m·°C) |
Specific thermal capacity (J/kg·°C) |
Specific electrical resistivity (Ω mm²/m) |
Density (kg/dm³) |
Poisson’s coefficient, ν |
---|---|---|---|---|---|---|---|
43 | - | - | 0.22 | - | |||
961 | 412 | - | 44.3 | 331 | - | ||
595 | - | 24 | 33.2 | 432 | 221 |
Heat treated : 1494°C - 1824°C
Grade | Standard | Country | Application |
---|---|---|---|
X2CrNiMo18-14-3 | |||
X2CrNiMo18-15-4 | |||
X2CrNiMo18-16-5 | |||
X2CrNiMo18-14-3 | |||
X2CrNiMo18-14-3 | |||
X2CrNiMo18-15-4 | |||
X2CrNiMo18-15-4 | |||
1.4435 | |||
1.4435 | |||
1.4435 | |||
1.4435 | |||
Z3CND17-11-02 | |||
Z3CND17-11-02 | |||
Z3CND17-11-02FF | |||
Z3CND17-11-02FF |
DIN 17440 (1996) | Stainless steels - Technical delivery conditions for drawn wire | DIN-17440-(1996).pdf |
DIN 17441 (1997) | Stainless steels - Technical delivery conditions for cold rolled strips and slit coils strip and sheets cut from such strips for pressure purposes | DIN-17441-(1997).pdf |
DIN 17455 (1985) | Welded circular tubes of stainless steels for general requirements; technical delivery conditions | DIN-17455-(1985).pdf |
DIN 17456 (1985) | Seamless circular tubes of stainless steels for general requirements; technical delivery conditions | DIN-17456-(1985)-.pdf |
DIN 17457 (1985) | Welded circular tubes of austenitic stainless steels for special requirements; technical delivery conditions | DIN-17457-(1985).pdf |
DIN 17458 (1985) | Seamless circular tubes of austenitic stainless steels for special requirements; technical delivery conditions | DIN-17458-(1985).pdf |
DIN EN 10028-7 | Flat products made of steels for pressure purposes - Part 7: Stainless steels | DIN-EN-10028-7.pdf |
DIN EN 10088-1 | Stainless steels - Part 1: List of stainless steels | DIN-EN-10088-1.pdf |
DIN EN 10088-2 | Stainless steels - Part 2: Technical delivery conditions for sheet/plate and strip of corrosion resisting steels for general purposes | DIN-EN-10088-2.pdf |
DIN EN 10088-3 | Stainless steels - Part 3: Technical delivery conditions for semi-finished products, bars, rods, wire, sections and bright products of corrosion resisting steels for general purposes | DIN-EN-10088-3.pdf |
DIN EN 10088-4 | Stainless steels - Part 4: Technical delivery conditions for sheet/plate and strip of corrosion resisting steels for construction purposes | DIN-EN-10088-4.pdf |
DIN EN 10088-5 | Stainless steels - Part 5: Technical delivery conditions for bars, rods, wire, sections and bright products of corrosion resisting steels for construction purposes | DIN-EN-10088-5.pdf |
DIN EN 10216-5 (2004) | Seamless steel tubes for pressure purposes - Technical delivery conditions - Part 5: Stainless steel tubes | DIN-EN-10216-5-(2004)-.pdf |
DIN EN 10217-7 | Welded steel tubes for pressure purposes - Technical delivery conditions - Part 7: Stainless steel tubes | DIN-EN-10217-7.pdf |
DIN EN 10222-5 | Steel forgings for pressure purposes - Part 5: Martensitic, austenitic and austenitic-ferritic stainless steels | DIN-EN-10222-5.pdf |
DIN EN 10250-4 | Open die steel forgings for general engineering purposes - Part 4: Stainless steels | DIN-EN-10250-4.pdf |
DIN EN 10253-3 | Butt-welding pipe fittings - Part 3: Wrought austenitic and austenitic-ferritic (duplex) stainless steels without specific inspection requirements | DIN-EN-10253-3.pdf |
DIN EN 10253-4 | Butt-welding pipe fittings - Part 4: Wrought austenitic and austenitic-ferritic (duplex) stainless steels with specific inspection requirements | DIN-EN-10253-4.pdf |
DIN EN 10272 | Stainless steel bars for pressure purposes | DIN-EN-10272.pdf |
DIN EN 10296-2 (2005) | Welded circular steel tubes for mechanical and general engineering purposes - Technical delivery conditions - Part 2: Stainless steel | DIN-EN-10296-2-(2005).pdf |
DIN EN 10297-2 (2005) | Seamless circular steel tubes for mechanical and general engineering purposes - Technical delivery conditions - Part 2: Stainless steel | DIN-EN-10297-2-(2005)-.pdf |
Our main peoducts of steel are many kinds of special steel, like tool steel, mould steel, alloy steel, alloy constructural steel, heat-resistant steel, high speed tool steel,spring steel and bearing steel , stainless steel and so on, which have formed 12 series and more than 350 varieties with n...
Rfq.: sales@longhaisteel.com