UNS K92810 Alloy Steel and Mechanical Properties, Chemical Element, Cross Reference, Datasheet.
Category | Type | Steel Grade | Standard | Country | Application |
---|---|---|---|---|---|
Steel Grades | Alloy Steel | UNS K92810 | |||
AISI 1330 |
|||||
SCr435 |
|||||
ASTM 51310 |
|||||
35Cr |
|||||
UNS G23300 |
|||||
SKS95 |
|||||
P |
|||||
M |
|||||
UNS J93005 |
|||||
ICI 6150 |
AISI Grade 18Ni (200) Maraging steel, Annealed
Categories: Metal; Ferrous Metal; Alloy Steel; Low Alloy Steel; Carbon Steel; Low Carbon Steel; Maraging steel
Material Notes: Applications: Bearings, Belleville springs, bolts, cannon recoil springs, rocket motor and missiles cases, couplings, load cells, flexures for guidance mechanisms of missiles, helicopter drive shafts, transmission shafts, fan shafts in commercial jet engines, aircraft wing components and forgings, aluminum die casting dies, cold forming dies, plastic molding dies, cores, pins, punches, and trim knees.
Key Words: maraging steels, UNS K92810, ASTM A538 (A), ASTM A579 grade 71
Physical Properties | Metric | English | Comments |
---|---|---|---|
Density | 8.00 g/cc | 0.289 lb/in³ | |
Mechanical Properties | Metric | English | Comments |
Hardness, Brinell | 290 | 290 | estimated, based on comparison with similar maraging steels. |
Hardness, Knoop | 311 | 311 | estimated, based on comparison with similar maraging steels. |
Hardness, Rockwell B | 99 | 99 | estimated, based on comparison with similar maraging steels. |
Hardness, Rockwell C | 30 | 30 | estimated, based on comparison with similar maraging steels. |
Hardness, Vickers | 301 | 301 | estimated, based on comparison with similar maraging steels. |
Tensile Strength, Ultimate | 965 MPa | 140000 psi | |
Tensile Strength, Yield | 660 MPa | 95700 psi | estimated, based on comparison with similar maraging steels. |
Elongation at Break | 17.0 % | 17.0 % | estimated, based on comparison with similar maraging steels. |
Reduction of Area | 75.0 % | 75.0 % | estimated, based on comparison with similar maraging steels. |
Modulus of Elasticity | 183 GPa | 26500 ksi | |
Bulk Modulus | 140 GPa | 20300 ksi | Typical for steel |
Poissons Ratio | 0.300 | 0.300 | Calculated |
Shear Modulus | 70.0 GPa | 10200 ksi | Estimated from elastic modulus |
Electrical Properties | Metric | English | Comments |
Electrical Resistivity | 0.0000174 ohm-cm | 0.0000174 ohm-cm | Typical steel |
Thermal Properties | Metric | English | Comments |
CTE, linear |
10.1 µm/m-°C @Temperature 21.0 - 480 °C |
5.61 µin/in-°F @Temperature 69.8 - 896 °F |
|
Thermal Conductivity | 25.3 W/m-K | 176 BTU-in/hr-ft²-°F | 20°C |
25.8 W/m-K | 179 BTU-in/hr-ft²-°F | 50°C | |
27.0 W/m-K | 187 BTU-in/hr-ft²-°F | 100°C | |
Component Elements Properties | Metric | English | Comments |
Aluminum, Al | 0.10 % | 0.10 % | |
Boron, B | 0.0030 % | 0.0030 % | |
Carbon, C | <= 0.030 % | <= 0.030 % | |
Cobalt, Co | 8.50 % | 8.50 % | |
Iron, Fe | 69.0 % | 69.0 % | As remainder |
Manganese, Mn | <= 0.10 % | <= 0.10 % | |
Molybdenum, Mo | 3.25 % | 3.25 % | |
Nickel, Ni | 18.5 % | 18.5 % | |
Phosphorous, P | <= 0.010 % | <= 0.010 % | |
Silicon, Si | <= 0.10 % | <= 0.10 % | |
Sulfur, S | <= 0.010 % | <= 0.010 % | |
Titanium, Ti | 0.20 % | 0.20 % | |
Zirconium, Zr | 0.010 % | 0.010 % |
Users viewing this material also viewed the following:
AISI Grade 18Ni (250) Maraging Steel, nominal annealed properties
AISI Grade 18Ni (300) Maraging Steel nominal annealed properties
AISI Grade 18Ni (200) Maraging Steel, Aged, 16 mm round bar, tested in longitudinal direction
AISI Grade 18Ni (200) Maraging Steel, Aged, 32 mm round bar, tested in longitudinal direction
Overview of materials for Maraging Steel
M1820A / 7364
Yield Rp0.2 (MPa) |
Tensile Rm (MPa) |
Impact KV/Ku (J) |
Elongation A (%) |
Reduction in cross section on fracture Z (%) |
As-Heat-Treated Condition | Brinell hardness (HBW) |
---|---|---|---|---|---|---|
712 (≥) | 518 (≥) | 32 | 34 | 21 | Solution and Aging, Annealing, Ausaging, Q+T,etc | 232 |
Temperature (°C) |
Modulus of elasticity (GPa) |
Mean coefficient of thermal expansion 10-6/(°C) between 20(°C) and | Thermal conductivity (W/m·°C) |
Specific thermal capacity (J/kg·°C) |
Specific electrical resistivity (Ω mm²/m) |
Density (kg/dm³) |
Poisson’s coefficient, ν |
---|---|---|---|---|---|---|---|
33 | - | - | 0.23 | - | |||
923 | 694 | - | 31.3 | 133 | - | ||
181 | - | 32 | 43.2 | 211 | 413 |
Heat treated : 1268°C - 1327°C
Grade | Standard | Country | Application |
---|---|---|---|
UNS G10300 | UNS | USA | General use carbon steel bar |
UNS G10050 | UNS | USA | General use carbon steel bar |
UNS G10060 | UNS | USA | General use carbon steel bar |
UNS G10080 | UNS | USA | General use carbon steel bar |
UNS G10110 | UNS | USA | General use carbon steel bar |
ASTM 1012 | ASTM | USA | General use carbon steel bar |
UNS G10120 | UNS | USA | General use carbon steel bar |
UNS G10130 | UNS | USA | General use carbon steel bar |
UNS G10150 | UNS | USA | General use carbon steel bar |
UNS G10160 | UNS | USA | General use carbon steel bar |
UNS G10170 | UNS | USA | General use carbon steel bar |
UNS G10180 | UNS | USA | General use carbon steel bar |
UNS G10190 | UNS | USA | General use carbon steel bar |
UNS G10200 | UNS | USA | General use carbon steel bar |
UNS G10210 | UNS | USA | General use carbon steel bar |
UNS T72301 | UNS | USA | Carbon tool steel |
W2-A | ASTM | USA | Carbon tool steel |
UNS T72302 | UNS | USA | Carbon tool steel |
UNS S42800 | UNS | USA | Martensitic special steel |
UNS S43100 | UNS | USA | Martensitic special steel |
Our main peoducts of steel are many kinds of special steel, like tool steel, mould steel, alloy steel, alloy constructural steel, heat-resistant steel, high speed tool steel,spring steel and bearing steel , stainless steel and so on, which have formed 12 series and more than 350 varieties with n...
Rfq.: sales@longhaisteel.com